股票
板块
用户
资讯
首页
天眼
自选
发现
开户
首页
天眼
自选
发现
我的

北化工《ACS AMI》:垂直取向石墨烯纤维热界面材料 ,其导热率接近平行模型估算值且热接触电阻较低



成果简介



传统的基于弹性体的热界面材料(E-TIM)受制于高导热率与低热接触电阻之间的权衡关系,这限制了其在高功率芯片散热中的应用。本文,北京化工大学卢咏来研究员、北京林业大学李京超副教授、西安交通大学李豪祥助理教授等在《ACS Appl. Mater. Interfaces 》期刊发表名为“Through-Thickness Vertically Aligned Graphene-Fiber Thermal Interface Materials with Thermal Conductivity Approaching the Parallel-Model Estimate and Low Thermal Contact Resistance”的论文,研究开发了一种基于玻璃化聚合物的、贯穿厚度方向的垂直取向石墨烯纤维E-TIM,通过将垂直连续的导热路径与自适应聚合物界面相结合,解决了这一限制。


将连续的石墨烯纤维进行机械取向,使其浸渍于基于β-羟基酯玻璃化聚合物的聚二甲基硅氧烷基质中,并通过堆叠焊接组装,从而沿厚度方向形成致密、连续的热传导路径。当石墨烯纤维体积分数仅为16.71 vol %时,该E-TIM便实现了160.2 W m–1 K–1的超平面热导率,接近平行模型的估算值,表明石墨烯纤维的轴向热导率被高效转化为宏观的平面热传导。在玻璃态聚合物基体中进行的热激活酯交换反应,促成了应力松弛、层间焊接以及界面形态重构,将热接触电阻降低至 40 psi 条件下 14.4 mm2 K W?1。分子动力学模拟进一步表明,玻璃态聚合物诱导的界面重构使有效接触面积和界面热导率超越了常规粘弹性蠕变的水平。在器件级散热演示中,该电子热界面材料(E-TIM)通过将稳态热源温度降低20.8 °C,表现优于商用E-TIM,凸显了其在高功率芯片热管理方面的巨大潜力。



图文导读


Figure 1.(a) Schematic illustration of the stacking and cutting process for preparing VPDMS-VGF-TIM and the microstructure of filler alignment. (b) Comparison of the κ⊥ and Rc of VPDMS-VGF-TIM with previously reported TIMs. (c) Optical photograph of VPDMS-VGF-TIM cut by a precision cutting machine. (d) Cross-sectional scanning electron microscopy (SEM) image of VPDMS-VGF-TIM.


Figure 2.(a) Cross-sectional SEM image and fast Fourier transform (FFT) pattern of VPDMS-VGF-TIM (b, c) WAXD patterns and azimuth angle curves of VPDMS-RGF-TIM and VPDMS-VGF-TIM. (d) XRD patterns of VPDMS-RGF-TIM and VPDMS-VGF-TIM. (e) Schematics of the parallel and series models. (f) Comparison of the κ⊥ of the parallel model, the series model, and VPDMS-VGF-TIM at various GF contents. (g) Temperature dependence of the κ⊥ of VPDMS-VGF-TIM. The inset shows the temperature dependence of thermal diffusivity (α) and the specific heat capacity (Cp) of VPDMS-VGF-TIM. (h) Thermal stability of VPDMS-VGF-TIM during thermal cycling between 30 and 80 °C. (i) Comparison of the κ⊥ of this work with different fillers and filler contents with previously reported results.


Figure 3.Mechanical properties of VPDMS-VGF-TIM. (a) Tensile stress-strain curve of VPDMS-VGF-TIM. (b) Compressive stress-strain curves of VPDMS-VGF-TIM. (c) Comparison of compressive modulus and thermal conductivity of VPDMS-VGF-TIM with reported TIMs. (d) Thermal stability evolution of VPDMS-VGF-TIM after 1000 compressive cycles. The inset shows SEM images of VPDMS-VGF-TIM before and after 1000 compressive cycles. (e) Thickness evolution of the VPDMS-VGF-TIM after 1000 compressive cycles under 30% strain.


Figure 4.Thermal resistance measurements and vitrimer-enabled interfacial heat-transfer mechanism of VPDMS-VGF-TIM. (a) Rt of VPDMS-VGF-TIM under different pressures. (b) Comparison of Rc between VPDMS-VGF-TIM and PDMS-VGF-TIM under different pressures. (c) SEM images of VPDMS on Al substrate before and after hot pressing at 100 °C. (d) Cross-sectional view of the PDMS model relaxed at 40 °C (P40) in the yoz plane. (e) Cross-sectional view of the PDMS model relaxed at 80 °C (P80) in the yoz plane. (f) Cross-sectional view of the VPDMS model relaxed at 80 °C (V80) in the yoz plane. (g) Comparison of effective contact area, Aeff, for the P40, P80, and V80 models. (h) Comparison of interfacial thermal conductance (ITC) for the P40, P80, and V80 models. (i) Schematic diagram of the thermal resistance reduction mechanism of VPDMS-VGF-TIM.


Figure 5.Thermal interface performance and thermal management demonstration of VPDMS-VGF-TIM. (a) Photograph and schematic illustration of the TIM performance measurement system. (b) Top-view infrared thermal images of the ceramic heater at a power density of 40 W cm–2 as a function of heating time: with VPDMS-VGF-TIM, with a commercial TIM (THERMALRIGHT VALDR ODIN), and without TIM. (c) Steady-state temperature of the ceramic heater as a function of power density. (d) Evolution of the ceramic heater surface temperature with increasing input power density. (e) Temperature evolution of the ceramic heater as a function of heating time at a power density of 40 W cm–2. (f) Temperature variation of the ceramic heater during cyclic thermal loading tests at a power density of 30 W cm–2.



小结


综上所述,我们开发了一种基于玻璃体三聚体的垂直取向石墨烯纤维热界面材料(TIM),以解决聚合物基TIM中长期存在的挑战,即如何同时实现高面内热导率和低热接触电阻。连续的贯穿厚度方向的石墨烯纤维网络使石墨烯纤维的高轴向热导率能够直接促进平面内的热传导,从而在仅16.71体积百分比的石墨烯纤维填充量下,实现了160.2 W m–1 K–1的热导率。


β-羟基酯 VPDMS 不仅充当了柔性基体,还在界面调控中发挥了积极作用。动态酯交换反应在制备过程中实现了层间焊接,并在使用过程中促进了热激活应力松弛和界面形态重构。因此,VPDMS-VGF-TIM 在 40 psi 压力下实现了 14.4 mm2 K W?1 的低热接触电阻,同时保持了良好的机械顺应性和循环可靠性,包括 0.61 MPa 的压缩模量以及 1000 次压缩循环后 91.6% 的厚度恢复率。分子动力学(MD)模拟证实了玻璃态聚合物辅助的界面重构在提高有效接触面积和界面热导率方面的作用。器件级测试进一步证实了 VPDMS-VGF-TIM 的实际散热优势,与商用 TIM 相比,其稳态热源温度降低了 20.8 °C。总体而言,这项工作表明,将垂直连续的热网络与可重构的聚合物界面相结合,是设计兼具低体积电阻和低热接触电阻的高性能 TIM 的有效途径。


文献:

https://doi.org/10.1021/acsami.6c10738

信息来源:材料分析与应用1




2026中国国际石墨烯创新大会

11月13-15日 中国·温州

“2026年中国国际石墨烯创新大会”将由石墨烯产业技术创新战略联盟(CGIA)和正泰集团联合主办,将于2026年11月13-15日在温州市(乐清)举办。大会聚焦石墨烯应用市场,着力促进石墨烯创新成果与产业端的深度对接合作,推动石墨烯产业迈向高质量发展新阶段。2026中国国际石墨烯材料应用博览会将同期举办。


点击下方链接,了解大会详情:

??官宣 | 关于召开2026中国国际石墨烯创新大会的通知

??重磅征稿|2026 中国国际石墨烯创新大会论文征集通知

??报名通道已开启 | 2026中国国际石墨烯创新大会火热报名中~

??展商招募 | 2026中国国际石墨烯材料应用博览会


会务组电话:

4001103655

13264226602(微信同号)

13260327636(微信同号)

16601148110(微信同号)

注:添加微信请备注姓名+单位




FOCUS

重点关注


??联盟理事单位招募 | 联合前行,共赢未来~

??石墨烯联盟(CGIA)广告投放服务合作指南

??2026,与CGIA同行:您的每一个需求,我们都将全力以赴!

??【需求对接】需采购铜包石墨烯漆包线

??【需求对接】需采购高导电型导体材料、电磁屏蔽用的柔性材料、高导热型导体/屏蔽材料

??【需求对接】需采购胶辊用石墨烯改性橡塑材料

??【采购需求】耐高温耐磨石墨烯防腐涂料

??【需求对接】聚焦产业技术突破 阀门龙头企业公开四大合作攻关需求

??项目征集|石墨烯铝基导电、导热产业化项目火热征集中

??《全球石墨烯产业研究报告系列丛书》

??【需求对接】需采购石墨烯粉体

??关于征集石墨烯及新材料在汽车、医药、农业等应用领域的产业化项目的通知






我们的视频号


  “石墨烯联盟”视频号里面,有备受瞩目的“烯”世奇材,有惊喜连连的大咖开讲,有生动有趣的科普视频,甚至还有不定期的“福利”乱入...欢迎大家扫码关注我们的视频号,将满满的干货收入囊中~


我们的视频号



原文链接
多空观点 观点仅供交流,不构成投资建议
点赞
踩一踩
收藏
分享

评论 (0)

0/200
声明:社区内容仅代表用户个人观点,不构成任何投资建议。投资有风险,入市需谨慎。