股票
板块
用户
资讯
首页
天眼
自选
发现
开户
首页
天眼
自选
发现
我的

中科院宁波材料所Carbon: 双尺度碳纳米管网络, 破解CFRP电热除冰性能衰减难题


开发具有高效电热功能的碳纤维增强聚合物(CFRP)对于缓解关键基础设施的表面结冰问题至关重要。为此,嵌入碳纳米管(CNT)夹层可实现多功能CFRP,将电热除冰与层间增韧相结合。然而,实际应用面临两大挑战:CNT在宏观组装过程中本征性能的损失,以及CNT组装体在复合材料制备过程中电热性能的退化。

本文,中国科学院宁波材料技术与工程研究所黄其忠团队提出了一种协同策略。首先,将取向的连续碳纳米管纤维薄膜(CNTFs)嵌入作为电热层,以确保导电网络的连续性。制备的CNTF/CFRP在低电压(≤ 10 V)下表现出良好的电热性能,表面平衡温度约为200 °C。其次,通过溶剂辅助预浸渍,利用掺入不连续短碳纳米管(0.5~2 μm)的方式,局部增强了CNTF内部纤维间树脂的导电性。随着分级碳纳米管-CNTF导电网络的建立,CNT-CNTF/CFRP复合材料的电热性能得到了进一步提升。与CNTF/CFRP相比,其稳态表面温度提高了120.5%,且在300秒内平均升温速度快了55.2%。这种双尺度协同策略在保持CFRP轻质、薄型特性的同时,还提供了高电热转换效率,在苛刻的应用场景中具有巨大的潜力。相关论文以“Efficient Electrothermal Carbon Fiber-Reinforced Composites Enabled by the Synergistic Integration of Embedded Continuous Carbon Nanotube Fiber Films and Discrete Carbon Nanotubes”为题,发表在《Carbon》上。

图1|  (a) Layered structural model of CNTF/CFRP. (b) Schematic of the CNTF/CFRP fabrication process. (c) Photograph of CNTF. (d) Photograph of CNTF/CFRP. (e) SEM image of CNTF. (f) SEM image of delamination failure surface of CNTF/CFRP in electric heating layer. (g) Z-directional cross-sectional image of CNTF/CFRP captured by a super-depth optical microscope. (h) Partial enlarged view of (g). (h1) SEM close-up of the electrothermal layer area corresponding to (h). (i) Thermogravimetric curve of CNTF/CFRP in air. (j) Thermogravimetric curve of CNTF/CFRP in nitrogen.图2| (a) Power density applied to the electrothermal layer as a function of voltage. (b) Variation of the electrical resistance of the electrothermal layer with voltage. (c) Thermal response curves of the CFRP surface (voltages: 2 ~ 10 V). Steady-state thermal distribution images (d1, e1) of the CFRP surface before (d) and after (e) power application, along with the corresponding three-dimensional temperature distribution maps of the CNTF-covered region (d2, e2) and the temperature distribution histogram of the central heat source region (e3). The thick white rectangular boxes indicate the laminate regions, while the orange dashed boxes denote the CNTF-covered regions. The thin white boxes indicate the central heat source regions, where both ends of the CNTF are directly connected to the copper foil. The white shaded regions represent the CNTF-covered regions outside the central heat source area.图3|  At an applied voltage of 8 V: (a) power density applied to the electrothermal layers of 0° and 90° samples. (b) Thermal response curves and (c) equilibrium temperature of the 0° and 90° CFRP sample surfaces. (d) Thermal response rate curves corresponding to (b). Infrared thermal images of the 0° (e) and 90° (f) samples, along with their corresponding three-dimensional temperature distribution maps (e1, f1). (g) Linear temperature distribution curves of 0° and 90° samples, with the corresponding line positions indicated in (e) and (f).图4|  Under an applied voltage of 8 V: (a) thermal response curves, (c) equilibrium temperature and (d) thermal response rate curves of CFRP samples incorporating 5, 10 and 15 μm CNTF interlayers. (b) power density applied to the electrothermal layers of each sample. (e) infrared thermographic images of the 5~15 μm samples at steady state. Ultrasonic-depth microscopic cross-sectional images of CNTF/CFRP in the interlaminar region: (f) CFRP with 5 μm CNTF; (g) CFRP with 10 μm CNTF; (h) CFRP with 15 μm CNTF. (i) Variation in the resistance of the electrothermal layer with CNTF thickness.图5|  Schematic diagrams of (a) pure CNTF, (b) embedded CNTF layer and (c) CNTF/CFRP composite. Under an applied voltage of 8 V, (d) thermal response curve of pure CNTF; (e) thermal response curves of the CNTF composite layer and the surface of the CNTF/CFRP composite.图6|   (a) Schematic of the CNT deep impregnation process. (b) morphology of the CNTs used for modification. (c) Thermal response curves, (e) equilibrium temperatures, and (f) Thermal response rate curves of baseline and CFRP samples treated with dispersions of varying CNT concentrations under an 8 V input. (d) Power density applied to the electrothermal layers of each sample.图7|  Infrared thermal images at steady state for the baseline (a) and 0.0 % (b) samples. Infrared thermal images of the 1.0 % specimen near steady state before (c) and after (d) damage. (d1) Photograph of the 1.0 % sample after testing. (e) 3D infrared surface temperature maps of the baseline and 1.0 % CFRP laminates, corresponding to (a) and (c), respectively. (f) Voltage-temperature data and the corresponding fitted curve for the 1.0 % specimen. (g) Electrothermal on-off cycling test of the 1.0 % sample (0 V/5 V switching).
图8|   (A) Electrical conductivity values of the electrothermal layers for the baseline and modified samples. (b) Schematic diagram of sampling for micro-morphology characterization. Delamination fracture surface images of the electrothermal layer in (c–d1) the baseline sample, and (e–f1) the 0.0?% sample. (d1) and (f1) are magnified views of the red dashed boxes in (d) and (f), respectively. Yellow boxes indicate regions resembling dry fiber bundles, while yellow dashed circles highlight voids caused by incomplete resin infiltration. (For interpretation of the references to colour in this figure legend, the reader is referred to the Web version of this article.)图9|  Schematic illustrations of the internal structures of CNTF composite films treated with CNT dispersions at concentrations of (a) 0.0 %, (b) 0.1 %, (c) 1.0 %, and (d) 2.0 %, along with (a1-d1) their corresponding cross-sectional SEM images. (a2-d3) Enlarged views of the regions highlighted by red dashed boxes in (a1-d1), respectively. (a3-c3, d4, d6) Delaminated cross-sections of the CNTF layers in electrothermal CFRP samples treated with 0.0 %, 0.1%, 1.0 %, and 2.0 % CNT dispersions. (a4-c4, d5, d7) Enlarged views corresponding to the red dashed boxes in (a3-c3, d4, d6). Yellow dashed rectangles indicate resin-rich regions. Yellow dashed circles indicate CNTs embedded in the resin. Green dashed circles indicate CNTFs embedded in the resin. Yellow arrows indicate CNTs entangled between CNTFs in the delaminated cross-sectional views.

本研究致力于解决两个长期制约碳纳米管(CNT)交错碳纤维增强塑料(CFRP)复合材料电热性能的难题:宏观组装过程中碳纳米管固有性能的丧失,以及树脂浸渍导致的导电性衰减。我们提出了一种高效电热复合材料结构,该结构将单向连续碳纳米管纤维(CNTF)与离散碳纳米管协同集成,形成了一个分级、跨尺度的导电网络。

针对该材料体系进行了分层研究。将未经改性的碳纳米管纤维(CNTF)薄膜作为核心加热元件嵌入碳纤维增强塑料(CFRP)层压板层之间。中心加热区表现出均匀且高效的电热耦合,在低电压(≤10 V)运行下,表面温度可达近200 °C。该系统表现出显著的各向异性行为,其电热性能对CNTF取向极为敏感。沿电流方向对齐碳纳米管纤维可最大化导电性和发热量,而增加碳纳米管纤维厚度则进一步提高了稳态温度和加热速率。

为抵消树脂浸渍引起的导电性损失,我们引入了一种结合纳米级碳纳米管的溶剂辅助预浸渍策略。这使得能够对碳纳米管纤维内富含树脂的纤维间区域进行精确掺杂,在构建二级导电网络的同时,促进了树脂浸渍和界面接触。在 1% 的最佳 CNT 浓度下,改性复合材料的稳态温度较基准样品提高了 120%,热响应速率和功率密度也显著提升。然而,超过该阈值会导致分散不稳定和 CNT 团聚,从而引发“CNTF 纤维过滤”效应,阻碍树脂浸渍并降低性能。

综上所述,所开发的CNT-CNTF/CFRP复合材料兼具轻量化、结构完整性和卓越的电热性能。其除冰效果已通过结冰/除冰实验得到验证。这种分级导电网络设计为严苛环境下的快速加热和除冰提供了可扩展且耐用的解决方案。本研究不仅深化了对多功能碳纤维增强塑料(CFRP)系统中结构-性能关系的基础理解,还为航空航天、能源和交通运输领域的下一代热管理应用提供了坚实的平台。

原文:DOI:10.1016/j.carbon.2026.122063


信息来源:Carbontech




2026中国国际石墨烯创新大会

11月13-15日 中国·温州

“2026年中国国际石墨烯创新大会”将由石墨烯产业技术创新战略联盟(CGIA)和正泰集团联合主办,将于2026年11月13-15日在温州市(乐清)举办。大会聚焦石墨烯应用市场,着力促进石墨烯创新成果与产业端的深度对接合作,推动石墨烯产业迈向高质量发展新阶段。2026中国国际石墨烯材料应用博览会将同期举办。


点击下方链接,了解大会详情:

??官宣 | 关于召开2026中国国际石墨烯创新大会的通知

??重磅征稿|2026 中国国际石墨烯创新大会论文征集通知

??报名通道已开启 | 2026中国国际石墨烯创新大会火热报名中~

??展商招募 | 2026中国国际石墨烯材料应用博览会


会务组电话:

4001103655

13264226602(微信同号)

13260327636(微信同号)

16601148110(微信同号)

注:添加微信请备注姓名+单位




FOCUS

重点关注


??联盟理事单位招募 | 联合前行,共赢未来~

??石墨烯联盟(CGIA)广告投放服务合作指南

??2026,与CGIA同行:您的每一个需求,我们都将全力以赴!

??【需求对接】需采购铜包石墨烯漆包线

??【需求对接】需采购高导电型导体材料、电磁屏蔽用的柔性材料、高导热型导体/屏蔽材料

??【需求对接】需采购胶辊用石墨烯改性橡塑材料

??【采购需求】耐高温耐磨石墨烯防腐涂料

??【需求对接】聚焦产业技术突破 阀门龙头企业公开四大合作攻关需求

??项目征集|石墨烯铝基导电、导热产业化项目火热征集中

??《全球石墨烯产业研究报告系列丛书》

??【需求对接】需采购石墨烯粉体

??关于征集石墨烯及新材料在汽车、医药、农业等应用领域的产业化项目的通知






我们的视频号


  “石墨烯联盟”视频号里面,有备受瞩目的“烯”世奇材,有惊喜连连的大咖开讲,有生动有趣的科普视频,甚至还有不定期的“福利”乱入...欢迎大家扫码关注我们的视频号,将满满的干货收入囊中~


我们的视频号



原文链接
多空观点 观点仅供交流,不构成投资建议
点赞
踩一踩
收藏
分享

评论 (0)

0/200
声明:社区内容仅代表用户个人观点,不构成任何投资建议。投资有风险,入市需谨慎。